Fusion Electronics Car Amplifier CA AM20350 User Manual

AMPLIFIERS  
CA-AM10900 CA-AM20350 CA-AM20650 CA-AM40700 CA-AM41200  
AMPLIFIER SPECIFICATIONS  
CA-AM10900  
CA-AM20350  
350  
CA-AM20650  
650  
CA-AM40700  
700  
CA-AM41200  
1200  
Peak Power (Watts)  
900  
Frequency Response 15Hz - 185Hz  
10Hz -100kHz  
10Hz -100kHz  
10Hz -100kHz  
10Hz -100kHz  
Dimensions (mm)  
267(l) x 230(w) x 49(h)  
267(l) x 230(w) x 49(h)  
377(l) x 230(w) x 49(h)  
377(l) x 230(w) x 49(h)  
457(l) x 230(w) x 49(h)  
10-1/2 x 9-1/16 x 1-15/16” 10-1/2 x 9-1/16 x 1-15/16” 14-27/32 x 9-1/16 x 1-15/16” 14-27/32 x 9-1/16 x 1-15/16” 18 x 9-1/16 x 1-15/16”  
Power Ratings  
300W RMS x 1  
55W RMS x 2  
115W RMS x 2  
50W RMS x 4  
110W RMS x 4  
@ 4Ω 1% THD+N,  
@ 4Ω 1% THD+N,  
@ 4Ω 1% THD+N,  
@ 4Ω 1% THD+N,  
@ 4Ω 1% THD+N,  
480W RMS x 1  
85W RMS x 2  
170W RMS x 2  
80W RMS x 4  
150W RMS x 4  
@ 2Ω 1% THD+N  
@ 2Ω 1% THD+N,  
@ 2Ω 1% THD+N,  
@ 2Ω 1% THD+N,  
@ 2Ω 1% THD+N,  
175W RMS x 1  
@ 4Ω Bridged  
1% THD+N  
340W RMS x 1  
@ 4Ω Bridged  
1% THD+N  
160W RMS x 2  
@ 4Ω Bridged  
1% THD+N  
300W RMS x 2  
@ 4Ω Bridged  
1% THD+N  
INSTALLATION GUIDELINES  
1. Ensure the +12V lead is disconnected from the battery before you connect any new equipment.  
2. Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.  
3. Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the event of an accident.  
4. Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.  
5. Ensure the mounting location has sufficient air flow around the amplifier. If the amplifier is mounted in an enclosed space a  
3” fan with ducting should be used to aid in air flow.  
6. Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the amplifier.  
7. Ensure you use the recommended gauge wire/cable for all amplifier connections.  
WIRING  
REMOTE TURN ON  
Ensuretheaudiosystemisturnedoffbeforemakinganyconnections  
to the amplifier, speakers or source unit.  
This connection turns the amplifier on and should be connected to  
the remote turn on wire from the Head Unit. If one is not available  
a switched 12v source must be used. Either a power antenna wire  
or ACC +12V.  
Failure to do so could result in permanent damage to the audio  
system. When wiring the FUSION amplifier ensure that the cable  
is protected from sharp objects and always use rubber grommets  
when wiring through metal panels.  
Ensure all terminals and connections are protected from the  
vehicle chassis and from each other as failure to do so could result  
in permanent damage to the audio system.  
LOW LEVEL INPUTS  
Choose the correct length RCA interconnects and run them to the  
RCA outputs of the source/head unit, avoiding running beside other  
looms and or power cable.  
POWER  
LEVEL CONTROL  
FUSION amplifiers should be connected directly to the +12V battery  
terminal with an inline fuse or circuit breaker as close to the battery  
as possible.  
This control is used to match the input level of the amplifier to the  
output level of you head unit. We recommend the following method.  
1. Turn the amplifier level to zero  
2. Turn the volume of the head unit to ¾ and the bass and treble  
to zero  
GROUND  
When grounding/earthing your amplifier ensure that the location  
is a good source of ground (preferably the floor pan). Make sure  
the metal is clean of paint etc as a poor earth could damage your  
audio system.  
3. Adjust the level control until the desired maximum volume is  
achieved without distortion.  
4. Failure to follow these steps may cause permanent damage to  
the audio system.  

ATN 7800c User Manual
Canon 512XL User Manual
Canon Camera Accessories 580EX User Manual
Canon XF100 User Manual
Hamilton Beach 52230C User Manual
Hitachi VM E520A User Manual
Hypertec N14628KHY User Manual
IRIS LLNR User Manual
JVC CD Receiver KD G407 User Manual
JVC GR SXM75ED User Manual